粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

UL 94 用來評價材料在被點燃后火焰熄滅的能力。根據燃燒速度、燃燒時間、抗滴落能力以及滴落物是否燃燒等有多種評判方法。每種被測材料根據顏色或厚度都可以得到許多值。當選定某個產品的材料時，其 UL 等級應滿足塑料零件壁部分的厚度要求。UL 等級必須與厚度值一起報告。

1 Scope

1.1 These requirements cover tests for flammability of polymeric materials used for parts in devices and appliances. They are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application.

1.2 The methods described in this Standard involve standard size specimens and are intended to be used solely to measure and describe the flammability properties of materials, used in devices and appliances, in response to a small open flame or radiant heat source under controlled laboratory conditions.

1.3 The tests in the Standard for Tests for Flammability of Small Polymeric Component Materials should be used to evaluate small components which contain materials that can not be fabricated into standardized specimens in the minimum use thickness and subjected to applicable preselection tests in UL 94. Test procedures in UL 1694 are applicable to small components with an overall volume of less than 2500 mm3 (0.15 in3). UL 1694 is generally not applicable to small components with an overall volume greater than 2500 mm3 (0.15 in3).

1.4 The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standards applicable to such equipment. The flammability classification required of a material is dependent upon the equipment or device involved and the particular use of the material. The performance level of a material determined by these methods shall not be assumed to correlate with its performance in end-use application. The actual response to heat and flame of materials depends upon the size and bbbb, and also on the end-use of the product using the material. Assessment of other important characteristics in the end-use application includes, but is not limited to, factors such as ease of ignition, burning rate, flame spread, fuel contribution, intensity of burning, and products of combustion.

1.5 If found to be appropriate, the requirements are applied to other nonmetallic materials.

1.6 These tests, with the exception of the Radiant Panel Test in Section 10, are not applicable to the evaluation of parts where the thickness exceeds 13.0 mm or where the surface area exceeds 1 m2. These requirements do not cover polymeric materials when used for building construction, finishing, or contents such as wall and floor coverings, furnishings, decorative objects and so forth. In addition, the fire resistance (in terms of an hourly rating), flame spread, smoke characterization, and heat release rate is not evaluated. Other fire tests exist and shall be used to evaluate the flammability of materials in the intended end-use-product configuration.

代理范圍:

(一)水平燃燒測試,94HB,并指導前期打樣送測;

(二)垂直燃燒測試,94V-2,94V-1,94V-0,并指導前期打樣送測;

電子線UL758認證，燈具UL認證，電線電纜UL認證，QMMY2 UL746D注塑件認證，UL969 PGDQ2標簽認證，連接器UL認證，燈飾CCC認證，線路板組裝VZQC2認證，UL969 PGAA標簽認證，UL588圣誕產品認證，軟線UL62認證代理，PCBA線路板組裝ZPVI2認證，電容UL認證，開關UL認證，網絡線UL444認證，鋰電池、鎳錳電池UL認證，水晶頭UL1863認證，導電泡棉UL認證，光伏電纜UL認證，UL817插頭認證，ECBT2 UL1997連接器認證，熱縮套管UL認證，功率線UL13認證，UL507直流交流風扇認證，UL最新RSCS環保認證，阻燃套管UL認證，火災報警線UL1424認證，UL2089車載充電器認證，UL1059端子臺認證，塑膠電鍍處理UL認證，光纖UL1651認證，UL355卷線器認證，UL486接線端子認證，UL486接線端子認證 塑膠料QMFZ2認證，UL764線束認證，UL310快接端子認證，UL1446絕緣系統認證，開關VDE認證，各國電線電纜認證，各國插頭認證
詳詢Sunny陶13913142465 QQ1822971259