產品規格書
PRODUCT SPECIFICATION
【1】適用范圍 SCOPE
本規格書適用于：1.25間距條形連接器 (SMT)
This specification covers the 1.25mm(SMT) Pitch Bar Connectors series.
【2】產品名稱及型號 PRODUCT NAME AND PART NUMBER
產品名稱Product Name | 產品型號Part Number |
1.25連接器 | 1.25-C/D-nPB/nPWB |
| |
【3】定格 RATINGS
項目Item | 規 格Requirement |
| 大容許電壓Rated Voltage(MAX) | 100V | [AC(有效值 virtual value)/DC] |
| 大容許電流Rated Current(MAX) | 1.0A |
| 使用溫度范圍 Ambient temperature Range | -20℃～ +85℃ |
| | | |
【4】性能 PERFORMANCE
4.1電氣性能 Electrical Performance
項目Item | 條件 Test Condition | 規格Requirement |
| 4.1.1 | 接觸電阻Contact Resistance | 適合嵌合狀態；開放電壓20mV以下；短路電流10mA的狀態下測定。Mate applicable and measure by dry circuit，20mV MAX，10mA. | ≤20 mΩMAX |
| 4.1.2 | 絕緣電阻Insulation Resistance | 適合嵌合狀態；相鄰端子間或端子與地面間加DC 500V下測定。Mate applicable and apply 500V DC between adjacent terminal or ground. | 500MΩMIN |
| 4.1.3 | 耐電壓Dielectric | 適合嵌合狀態；相鄰端子間或端子與地面間加AC 500V（有效值）歷時1分鐘下測定。Mate applicable and apply 500V AC（virtual value）for 1minute between adjacent terminal or ground. | 無擊穿現象 No Breakdown |
4.2機械性能 Mechanical Performance
項目Item | 條件 Test Condition | 規格Requirement |
| 4.2.1 | 插入力及拔出力Insertion and Withdrawal Force | 用每分鐘25±3mm的速度；平行地插入、拔出。Insert and extract applicable at the speed rate of 25±3mm/minute. | 插入力Insertion5 * n (N) MAX拔出力Withdrawal0.3 * n (N) MIN |
| 4.2.2 | 端子保持力Terminal Retention Force | 單一端子；以用每分鐘25±3mm的速度平行向外拉Pull the terminal at the speed rate of 25±3mm per minute | 10 N MIN |
4.3環境和其他性能 Environmental Performance and Others
項目Item | 條件 Test Condition | 規格Requirement |
| 4.3.1 | 重復插拔Repeated Insertion and Withdrawal | 無通電狀態；以10次/分鐘的速度插拔20次Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute | 接觸抵抗Contact Resistance | 60 mΩMAX |
| 4.3.2 | 溫度上升Temperature Rise | 適合嵌合狀態；大容許電流通電，溫度測定。（UL 498）Carrying rated current load.（UL 498） | 溫度上升Temperature Rise | 30℃MAX |
項目Item | 條件 Test Condition | 規格Requirement |
| 4.3.3 | 耐振動性Vibration | DC 1mA通電狀態下；嵌合軸沿XYZ三個方向振動；振幅1.5mm；頻率10-55-10Hz/分；歷時2小時Amplitude：1.5mm P-PSweep time：10-55-10Hz in 1 minuteDuration：2 hours in each X.Y.Z. axes | 外觀 Appearance | 無損壞 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
瞬斷 Discontinuity | 1 ms MAX. |
| 4.3.4 | 耐沖擊性Shock | DC 1mA通電狀態下；嵌合軸沿相互垂直的6個方向；以490m/s2{50G}沖擊；各3次490m/s2{50G}，3 strokes in each X.Y.Z. axes. | 外觀 Appearance | 無損壞 No Damage |
瞬斷 Discontinuity | 1 ms MAX. |
| 4.3.5 | 耐熱性HeatResistance | 適合嵌合狀態；85±2℃的空氣中；放置96小時；再回到室溫中放置1-2小時85±2℃，96 hour | 外觀 Appearance | 無損壞 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
| 4.3.6 | 耐寒性ColdResistance | 適合嵌合狀態；-40±2℃的空氣中；放置96小時；再回到室溫中放置1-2小時-40±2℃，96 hour | 外觀 Appearance | 無損壞 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
| 4.3.7 | 耐濕性Humidity | 適合嵌合狀態；40±2℃、相對濕度90-95%的空氣中；放置96小時；再回到室溫中0.5小時內測定Temperature：40±2℃Relative Humidity：90-95%Duration：96 Hours | 外觀 Appearance | 無損壞 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
耐電壓 Dielectric Strength | 必須滿足4.1.3 Must meet 4.1.3 |
絕緣抵抗 Insulation Resistance | 100 MΩMIN |
| 4.3.8 | 溫度循環TemperatureCycling | 適合嵌合狀態；-55±3℃ 30分鐘；常溫常濕 10-15分鐘；85±2℃ 30分鐘；常溫常濕 10-15分鐘，循環5次。5 cycles of： a) -55±3℃ 30 minutesb) 85±2℃ 30 minutes | 外觀 Appearance | 無損壞 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
項目Item | 條件 Test Condition | 規格Requirement |
| 4.3.9 | 耐鹽霧性Salt Spray | 適合嵌合狀態；35±2℃、5±1%的鹽水噴霧48小時；試驗后常溫水洗；再室溫干燥。48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃. | 外觀 Appearance | 無損壞、腐蝕 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
| 4.3.10 | 耐亞硫酸SO2 Gas | 適合嵌合狀態；40±2℃、50±5ppm的亞硫酸中放置24小時24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. | 接觸抵抗 Contact Resistance | 60 mΩMAX |
| 4.3.11 | 耐氨性NH3 Gas | 適合嵌合狀態；濃度為28%的氨水容器中；放置40分鐘。40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution | 外觀 Appearance | 無損壞 No Damage |
接觸抵抗 Contact Resistance | 60 mΩMAX |
| 4.3.12 | 可焊性Solder ability | 端子前端浸入235±5℃的錫槽中；歷時2±0.5 sec。Soldering Time：2±0.5 sec.Soldering Temperature：235±5℃0.2 mmfrom terminal tip | 沾敷性 Solder Wetting | 沾敷面積95%以上 |
| 4.3.13 | 耐焊接熱Resistance toSoldering heat | 端子前端浸入260±5℃的錫槽中；歷時5±0.5 sec。Soldering Time：5±0.5 sec.Soldering Temperature：260±5℃0.2 mmfrom terminal tip | 外觀 Appearance | 無損壞、變形 No Damage |
( )：參考規格Reference Standard
{ }：參考單位Reference Unit
【5】外觀形狀、寸法及材質PRODUCT SHAPE,DIMENSIONS AND MATERIALS
圖面參照 Refer to the drawing.
名稱NAME | 材質MATERIALS |
| 基座Housing | LCP UL 94V-0 |
| 插簧Contact | 磷青銅 Phosphor Bronze |
| 備注Remark | 金屬表面鍍錫 |
鉅明科技（外資）創建于1988年，是一家FFC/FPC扁平電纜連接器、條形連接器、板對板連接器及各類線束的專業制造商。公司從產品的設計、開發、生產到銷售提供一條龍服務，產品種類齊全，品質可靠穩定，部分產品已通過了美國UL和加拿大CSA國際認證，并取得了ISO900已成為多家知名企業的A級供應商
在線咨詢 
