粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

(2)改變轉速的方法：改變皮帶輪外徑或改變齒輪減速器傳動比，也可選用不同轉速的動力機。

(3)水泵轉速改變后，其流量(Q)、揚程(H)和功率(N)的變化關系如下式所示： Q1=Q*n1/n   H1=H*(n1/n)2    N1=N*(n1/n)3

 式中：Q1、H1、N．分別代表轉速改變后的流量、揚程和功率。 Q、H、N分別代表規定轉速下的流量、揚程和功率。

(4)水泵轉速提高后，耗用功率增加，吸上真空度降低，壽命縮短。過分提高轉速會發生其它事故，故應慎用。

(5)水泵轉速過分降低時，泵的使用效益低，為此，應盡量避免泵在過低轉速下運行。用戶應按性能曲線圖選擇使用。

蝸殼式混流泵@察布蝸殼式混流泵@350HW-4蝸殼式混流泵值得信賴

混流泵是介于離心泵和軸流泵之間的泵型需要把壓水室規劃成徑導游葉(正導葉)加上類球形泵殼的構造型式是葉輪內安穩的相對運動的條件。為此，請求在導葉中的螺旋線有些的液體，不受任何外力的效果。

2、允許吸上真空度[Hs]與必需汽蝕余量[NPSH]r的換算關系：

 [Hs]≈10-[HPSH]c

 [NPSH]r≈[NPSH]C+0.3

 式中：[Hs]-允許吸上真空度   米

 [NPSH]C-臨界汽蝕余量   米

 [NPSH]r-必需汽蝕余量   米

蝸殼式混流泵@察布蝸殼式混流泵@350HW-4蝸殼式混流泵值得信賴

 *特征描述

HW 型蝸殼式混流泵是按國家標準系列而設計的高節能產品。其性能指標均達到先進水平，省材節能效果顯著。延伸搜索：水環真空泵

（一）用途
HW型混流泵為臥式、單級、單吸、懸臂蝸殼式混流泵，適用于農田排灌、工業、城鎮給排水及船塢、碼頭引水等。延伸搜索：水環真空泵
（二）特點
體積小、重量輕、流量大、效率高，汽蝕性能好，區范圍寬廣而平坦，結構簡單，使用管理方法，維修容易。延伸搜索：水環真空泵
（三）型號說明
以250HW—8為例：
250—泵進（出）水口直徑為250毫米。
8—泵總揚長為8米。

（四）水泵的傳動方式
我廠生產的HW型系列混流泵均機（電）兩用，其轉動方式視各地區動力情況而定，訂貨時根據原動機的型號（功率、轉速）確定水泵的傳動方式，以定皮帶輪的大小或聯軸器的規格。延伸搜索：水環真空泵
（五）水泵轉向：
從水泵進水口看葉輪為逆時針方向旋轉（即箭頭所示的方向旋轉）。

蝸殼式混流泵@察布蝸殼式混流泵@350HW-4蝸殼式混流泵值得信賴

3混流泵泵體劇烈振動或產生噪音產生原因：水泵安裝不牢或水泵安裝過高；電機滾珠軸承損壞；水泵主軸彎曲或與電機主軸不同心，不平行等。解決辦法：裝穩水泵或降低水泵的安裝高度；更換電機滾珠軸承；彎曲的水泵主軸或調整好水泵與電機的相對位置�；炝鞅昧髁坎蛔惝a(chǎn)生原因：影響水泵流量不足多是吸水管漏氣，底閥漏氣；進水口堵塞；底閥入水深度不足；水泵轉速太低；密封環或葉輪磨損過大；吸水高度超標等。解決辦法：檢查混流泵吸水管與底閥，堵住漏氣源；清理混流泵進水口處的淤泥或堵塞物；底閥入水深度必須大于進水管直徑的1.5倍，加大底閥入水深度；檢查電源電壓，提高水泵轉速，更換密封環或葉輪；降低水泵的安裝位置，或更換高揚程混流泵。

Instructions for use (i) the HW mixed-flow pump is composed of main parts such as pump body, pump cover, impeller, pump shaft and bearing body. (Ii) The pump cover is a part of the pump connected to the inlet pipe, with a specified axial end gap between the end surface and the impeller (maintaining the specified axial clearance after eliminating the axial activity gap of the bearing). The gap is too small to produce friction, too large will lead to the pump pressure water reflux, so that the pump efficiency is reduced, through the increase or decrease adjustment paper pad to meet the required requirements of the gap. Extended search: Water ring Vacuum Pump (iii) The sealing device is composed of a filler letter, a water seal letter, a filler cover and a lead powder (or oil immersion) asbestos root. Its role is: 1, in the tea to prevent air inhalation pump, play a sealing role. 2. When pumping, prevent water from flowing out of the pump too much along the shaft. (Iv) Shaft application to protect the shaft does not make it directly friction with the filler, if long-term use found that the bushing wear too much, can change the bushing. (V) The two supports of the pump shaft are bearings in the bearing body, and the bearing has an appropriate amount of grease in its body to lubricate the bearings. (Vi) The baffle on the shaft prevents water from flowing into the bearing body along the pump, thus protecting the bearing and extending its service life.