粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

DRSP-I-DC信號放大器-美國Omega原裝詳細介紹

DRSP-I-DC

過程測量和控制儀器 ? 信號調節器和發射器 ? DRSP-I Series
直流電流信號分配器
DRSP-I SeriesOne 4 to 20 mA Input to Two 4 to 20 mA Outputs with Full Isolation
Zero and Span Adjustments for Each Output
Full 1200 V Input/Output/ Power Isolation
Input/Output Loop Status LEDs
Output Test Button for Each Channel
Built-In Loop Power Supplies for Sink/Source I/O
Split, Convert, Boost, and Rescale Process Signals
Split Process Signals for Control and Validation
Interface a Process Signal with Multiple Panel Meters, PLCs, Recorders, Data Acquisition, DCS, and SCADA Systems

產品描述
The DRSP-I Series DC current signal splitters accept one 4 to 20 mA current input and provide two optically isolated 4 to 20 mA current outputs that are linearly related to the 4 to 20 mA current input. This provides an economical solution when one signal must be sent to two different devices. Typical applications include isolation, output splitting, output device separation and redundancy (i.e. to prevent failure of the entire loop if one device fails), or a combination of these. The input signal is filtered, amplified, split, and then passed through an opto-coupler to the output stages. Full 4-way isolation (input, output 1, output 2, power) make this module useful for ground loop elimination, common mode signal rejection,and noise pickup reduction.

Specifications
Input
Input Range: 4 to 20 mA
Input Impedance: 50 Ω typical
Input Loop Power Supply: 15 Vdc ±10%, regulated, 25 mA; May be selectively wired for sinking or sourcing mA input
Loop Status LEDs: Variable brightness LEDs indicate I/O loop level and status; One for input, one for each output
Output
Output Range:
(Output 1 and Output 2): 4 to 20 mA; 20V compliance, 1000 Ω at 20 mA
Output Linearity: Better than ±0.1% of span
Output Zero and Span: Multi-turn zero and span potentiometers for each output channel to compensate for load and lead variations; ±15% of span adjustment range typical
Output Loop Power Supplies: One for each output channel; 20 Vdc nominal, regulated, 25 mA may be selectively wired for sinking or sourcing mA output
Output Ripple and Noise: Less than 10 mVRMS
Output Functional Test: Front buttons set each output to test level when pressed; Each test level potentiometer adjustable 0 to 100% of span
General
Response Time: 70 milliseconds typical
Common Mode Rejection: 120 dB minimum
Isolation (Full 4-Way Isolation): Input 1, output 1, output 2, power; 1200 VRMS minimum
Ambient Temperature Range: -10 to 60°C (14 to 140°F)
Stability: Better than ±0.04% of span per °C
Power:
DRSP-I: 60 to 265 Vac, 50/60 Hz or 85 to 300 Vdc, 6 W maximum
DRSP-I-DC: 9 to 30 Vdc or 10 to 32 Vac 50/60 Hz, 6 W maximum
Housing: IP40, mounts to standard 35 mm (1.37") DIN rail
Connectors: Eight 4-terminal removable connectors; 14 AWG maximum wire size
Dimensions: 45 W x 117 H x 122 mm D (1.78 x 4.62 x 4.81"); height includes connectors
 

產品編號   產品描述

DRSP-I  DC current signal splitter, 60 to 265 Vac, 50/60 Hz or 85 to 300 Vdc power     
DRSP-I-DC  DC current signal splitter, 9 to 30 Vdc or 10 to 32 Vac, 50/60 Hz power     
RAIL-35-1  35 mm DIN rail, 1 m (3.3') length  
RAIL-35-2  35 mm DIN rail, 2 m (6.6') length  
iDRN-PS-1000  Power supply (switching), 95 to 240 Vac input, 24 Vdc output at 850 mA
 

 DRSP-I-DC

DRSP-I-DC信號放大器-美國Omega原裝 相關產品

DRSP-I-DC信號放大器-美國Omega原裝 技術文章