粗大浓稠硕大噗嗤噗嗤h,精品人妻码一区二区三区,国产av无码专区亚洲精品,日韩a片无码毛片免费看小说

PLC企業資訊
    FA-80-12M1H顯微鏡檢查
    發布者:lingliang  發布時間:2023-02-04 13:01:08

          1. e2v commends to use E = 1 because of the limited EEPROM write cycles refer on page 12.

          2. Camera gain (dB) = G x 0.047. A and B gain value are set in manufacturing but can be adjust if necessary. 

          3. Commands “H=2” and “H=4” will give 10 and 15 MHz data rate which are not compatible with Camera Link standard. Please don’t use it.

          4. The pinout corresponding to this option is fully compatible with the Camera Link standard

          5. The test pattern is useful to check if the interfacing is well done. The user should see a jagged image of 256 pixels steps.

          6. The offset is set in manufacturing to balance both the channels. The initial setting is about 8 (~ 130 LSB). In some cases, the user may have to change it (for example if the ambient temperature is very high).

          7. To be used for multi-camera synchronization. Refer to Figure 8

          Synchronization Mode Four different modes may be defined under user control. The TRIG1 and TRIG2 signals may be used to trigger external events and to control the integration time. The Master clock is either external or internal clock. 8.1.1 Free Run Mode with Integration Time Setting The integration and readout periods start automatically and immediately after the previous period. The read-out time depends on pixel number and pixel rate. Note: 1. The integration time is set by the serial line and should be higher than the read-out time (otherwise it is adjusted to the readout time). Figure 8-1. Timing Diagram 8.1.2 Triggered Mode with Integration Time Setting The integration period starts immediately after the rising edge of TRIG1 input signal. The Integration time is set by the serial line. This integration period is immediately followed by a readout period. The read-out time depends on pixel number and the pixel rate. Table 8-1. Free Run Mode with Integration Time Setting

         Label Description Min Typ Max ti Integration time duration (1) – 13 ms tg Consecutive integration period gap (at maximum frequency) – 6 μs – tt Integration period stop to read-out start delay – 1 μs – 

        Triggered Mode with Integration Time Setting The integration period starts immediately after the rising edge of TRIG1 input signal. The Integration time is set by the serial line. This integration period is immediately followed by a readout period. The read-out time depends on pixel number and the pixel rate. Table 8-1. Free Run Mode with Integration Time Setting Label Description Min Typ Max ti Integration time duration (1) – 13 ms tg Consecutive integration period gap (at maximum frequency) – 6 μs – tt Integration period stop to read-out start delay – 1 μs – Integration N Readout N-1 Readout N Integration N+1 tt ti tg Table 8-2. Triggered Mode with Integration Time Setting Label Description Min Typ Max ti Integration time duration 5 μs – 13 ms td TRIG1 rising to integration period start delay – 5.5 μs –

    版權聲明PLC信息網轉載作品均注明出處,本網未注明出處和轉載的,是出于傳遞更多信息之目的,并不意味 著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權,或有其他諸如版權、肖像權、知識產權等方面的傷害,并非本網故意為之,在接到相關權利人通知后將立即加以更正。聯系電話:0571-87774297。
0571-87774297  
野花日本免费观看高清电影8| 老师久久精品人人爽人人爽澡| julia无码人妻中文字幕在线| 又粗又硬又黄a级毛片| 久久精品国产亚洲av高清色欲| 草草浮力影院| 被按摩师玩弄到潮喷在线播放 | 久久久久99精品成人片直播| 麻豆蜜桃av蜜臀av色欲av| 农村女妓女野外bbw| 国产乱子伦精品免费无码专区| 国产 国语对白 露脸| 亚洲av无码一区二区三区在线| 欧美一区二区三区激情| 精品人妻一区二区三区浪潮在线| 欧美日韩人妻精品一区二区三区| 我的初次内射欧美成人影视| 中文字幕乱码一区二区欧美 | 高h猛烈失禁潮喷a片在线观看| 老师脱了内裤让我进去| 精品福利一区二区三区免费视频| 精品无码国产自产拍在线观看| 把腿扒开做爽爽视频| 无码人妻aⅤ一区二区三区| 国产精品久久久久久久妇| 卡一卡2卡3卡精品网站| 中文字幕日本人妻久久久免费| 狠狠色丁香婷婷综合久久97| 天天躁日日躁aaaaxxxx| 夜鲁鲁鲁夜夜综合视频欧美| 亚洲av成人中文无码专区| 我老婆是冰山女总裁沈浪全集 | 亚洲欧美综合在线一区| 我被六个男人躁到早上小说| 色婷婷久久综合中文久久蜜桃av| 精品av无码国产一区二区| 最近中文国语字幕在线播放| 久久69国产精品久久69软件| 野花日本大全免费观看3中文版| 成人区人妻精品一区二区不卡网站 | 免费啪啪a片aaaa片老太婆交|