Storage of the Settings in EEPROM e2v recommends to use "E = 1" for settings that are often changed (check the maximum number of write cycles above) and when the time required by the camera to process a command is critical. The maximum number of write cycles allowed for the EEPROM is: 100 000. 10. Connector Description All connectors are on the rear panel. Note: Cables for digital signals shall be shielded twisted pairs. 10.1 Power Supply Camera connector type: Hirose HR10A-7R-6PB (male). Cable connector type: Hirose HR10A-7P-6S (female).
Table 10-1. Power Supply Connector Pin-out Signal Pin Signal Pin PWR 1 GND 4 PWR 2 GND 5 PWR 3 GND 6
Camera Link Connector Standard Camera Link cable shall be used to ensure the full electrical compatibility. Camera connector type: MDR-26 (female) ref. 10226-2210VE. Cable connector type: Standard Camera Link cable shall be used (ex. 3M - 14B26-SZLB-x00-OLC).
Table 10-2. Camera Link Connector Pin-out Signal Pin Signal Pin Signal Pin GND 1 CC2+ 10 X3+ 19 X0- 2 CC3- 11 SerTC- 20 X1- 3 CC4+ 12 SerTFG+ 21 X2- 4 GND 13 CC1+ 22 Xclk- 5 GND 14 CC2- 23 X3- 6 X0+ 15 CC3+ 24 SerTC+ 7 X1+ 16 CC4- 25 SerTFG- 8 X2+ 17 GND 26 CC1- 9 Xclk+ 18
Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name ODD-00 Tx0 ODD-07 Tx5 EVEN-02 Tx19 EVEN-09 Tx14 ODD-01 Tx1 ODD-08 Tx7 EVEN-03 Tx20 EVEN-10 Tx10 ODD-02 Tx2 ODD-09 Tx8 EVEN-04 Tx21 EVEN-11 Tx11 ODD-03 Tx3 ODD-10 Tx9 EVEN-05 Tx22 STROBE TxCLK ODD-04 Tx4 ODD-11 Tx12 EVEN-06 Tx16 LVAL Tx24 ODD-05 Tx6 EVEN-00 Tx15 EVEN-07 Tx17 ODD-06 Tx27 EVEN-01 Tx18 EVEN-08 Tx13 Table 10-4. Bit Assignments when used in 10-bit data (S = 1) Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name ODD-00 Tx0 ODD-07 Tx5 EVEN-02 Tx19 EVEN-09 Tx14 ODD-01 Tx1 ODD-08 Tx7 EVEN-03 Tx20 NC Tx10 ODD-02 Tx2 ODD-09 Tx8 EVEN-04 Tx21 NC Tx11 ODD-03 Tx3 NC Tx9 EVEN-05 Tx22 STROBE TxCLK ODD-04 Tx4 NC Tx12 EVEN-06 Tx16 LVAL Tx24 ODD-05 Tx6 EVEN-00 Tx15 EVEN-07 Tx17 ODD-06 Tx27 EVEN-01 Tx18 EVEN-08 Tx13 14 0889C–IMAGE–07/07 AViiVA® M2 CL e2v semiconductors SAS 2007 Table 10-5. Bit Assignments when used in 8-bit data (S = 2) Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name ODD-00 Tx0 ODD-07 Tx5 NC Tx19 EVEN-05 Tx14 ODD-01 Tx1 EVEN-00 Tx7 NC Tx20 EVEN-06 Tx10 ODD-02 Tx2 EVEN-01 Tx8 NC Tx21 EVEN-07 Tx11 ODD-03 Tx3 EVEN-02 Tx9 NC Tx22 STROBE TxCLK ODD-04 Tx4 EVEN-03 Tx12 NC Tx16 LVAL Tx24 ODD-05 Tx6 NC Tx15 NC Tx17 ODD-06 Tx27 NC Tx18 EVEN-04 Tx13
Mechanical Characteristics 11.1 Weight The camera typical weight (without lens nor lens adapter) is 220 g/7.7 ounces (typical). 11.2 Dimensions The camera dimensions (without lens) are W = 56 mm, H = 60 mm, L = 39.4 mm. Figure 11-1. Mechanical Box Drawing and Dimensions 15 15 6 39.4 12 4 x 2 holes M4 (on the 4 sides) 56 48 60 52 Sensor 1st pixel y = 30 ± 0.05 ? 42 H7 ? 46 z = 10.3 ± 0.03 Optical sensor plane to front face 1 3 x M2.5 at 120° x = refer to "Mechanical Mounting Reference" Reference mounting plane Reference mounting plane Reference mounting plane Mechanical reference point