Specifications for LT-200CL
Specifications LT-200CL
Camera Link Interface
Pin Signal Function
1 14 GND
2 15 Xo-/Xo+ CL Data
3 16 X1-/X1+ CL Data
4 17 X2-/X2+ CL Data
5 18 Xclk-/Xclk+ CL Clk
6 19 X3-/X3+ CL Data
7 20 SerTC+/SerTC- Serial in *
8 21 SerTFG-/SerTFG+ Serial out *
9 22 CC1-/CC1+ Trigger *
10 23 CC2-/CC2+ Reserved
11 24 CC3-/CC3+ Not used
12 25 CC4-/CC4+ Not used
13 26 GND
*) In Camera Link or 12 pin Hirose
Note:
Camera Link base configuration shown.
For medium configuration refer to Camera
Link specifications or operation manual.
HIROSE HR10A-10R-12PB-71
DC In / Trigger
Connection Pin-out
Pin 1 Ground
2 +12V to +24V DC
3 Ground
4 Reserved
5 Ground
6 RXD RS 232C*
7 TXD RS 232C*
8 Ground
9 XEEN output
10 Trigger input (TTL)*
11 —
12 Ground
Dimensions
Ordering Information
Front view (M52 mount)
Front view (Nikon F-mount)
Side view
Bottom view
Rear view
Spectral Response
Scanning system Line sensor with internal clock
Pixel clock 80.00 MHz
Line rate Standard
Programmable
32.9μs (Full resolution/binning/internal trigger)
32.9μs to 16.844ms, 12.5ns increments
Sensor 3 CMOS line sensors
mounted on RGB beam splitter prism
Sensor scanning width 28.672 mm
Cell size 14.0 (h) x 14.0 (v) μm
Active pixels 3 x 2048 (h)
3 x 1024 (h) with 2:1 binning
Sensitivity (sensor) Radiometric: 27nJ/cm2
Sensitivity (standard) 2800 Lux (7800K, gain = low,
shutter = OFF, G = 0 dB, F2.8, 100% video)
S/N ratio 57 dB on green with gain = 0 dB
Video output 24 bit (3 x 8) in CL base configuration
30 bit (3 x 10) in CL medium configuration
Gain Ref. set
Master tracking
Individual mode
Analog gain= Low (0dB) or High (+6dB)
Master: 0 dB to +8 dB
R, B: –2 dB to +6 dB
R/G/B: –2 dB to +14 dB
White balance Manual, fixed or one-push
Adjustable range 5000 K to 9000 K
Fixed: 4000 K, 4600 K or 5600 K
Knee correction Individual RGB knee point and slope
Shading correction Individual RGB flat or RB to G
Flat-field correction Two point pixel-to-pixel correction
Synchronization Internal X-tal or external trigger
Trigger modes No-shutter, shutter-select and pulse width control
Programmable exposure 25.8μs to 13.209 msec. in 12.5 ns increments
Functions controlled by
RS 232C or CL
Trigger modes, scan rate, exposure time, gain/
black level, shading correction,
flat-field correction, white balance,
knee-function, diagnostics
Diagnostics Test pattern generator (Color bar, gray pattern and
white). LED for power
Lens mount M-52 mount. (Standard)
Nikon F-mount. (Factory option)
Sensor alignment Better than ±0.1 mm
Operating temperature -5°C to +45°C/20 – 80% non-condensing
Storage temp./humidity -25°C to +60°C/20 – 80% non-condensing
Vibration 3G (20Hz to 200Hz, XYZ direction)
Shock 50G
Regulations Emission: CE CISPR Pub. 22 (EN55022)
Immunity: CISPR Pub. 24
IEC61000-4-2 Conforming level 4
FCC Part15 Class B
RoHS
Power 12V DC -10% to 24V DC +10%
450 mA (Typical) – 480 mA (Max.)
Dimensions 90 mm (H) x 90 mm (W) x 90 mm (D)
(without connector and lens mount protrusion)
Weight 830 g
April 2015
LT-200CL-M52 3 CMOS RGB Line Scan Camera. M52-mount (Standard)
LT-200CL -F 3 CMOS RGB Line Scan Camera. F-mount (Optional)
