Specifications for SW-4000T-MCL Sweep+ Series
Scanning system 3 high-speed CMOS line sensors, prism-mounted
Active pixels 3 x 4096 pixels (R, G, B)
Line rate Up to 67.7 kHz (variable)
Sensor width 30.72 mm
Pixel size Mode A: 7.5 μm x 7.5 μm
Mode B: 7.5 μm x 10.5 μm
Pixel clock (CL) 31.875 / 42.5 / 63.75 / 85 MHz
Video output Camera Link Base (8 bit - RGB8)
Camera Link Medium (8/10 bit - RGB8, RGB10)
Camera Link Full (8 bit - RGB8)
Camera Link Deca (8 bit - RGB8)
Object illuminance (min.) 220 lx @ 7800 K, Mode A
(Gain 18 dB, 525 μs exp., 50% video, RGB8)
Responsivity 123 DN/nJ/cm2
(G channel, Mode A, 10-bit @ 550 nm, 0 dB gain)
S/N ratio >55 dB on green, 10-bit with 0 dB gain
Inputs Trigger (Camera Link, TTL/75Ω via 12-pin or 10-pin)
Outputs LVAL, DVAL, EEN, XEEN (TTL)
Gain Analog Base Gain: 0 dB / 6 dB / 12 dB
Digital Master: 0 to +18 dB, R/B: -7.96 to +12 dB
Digital Individual: 0 to +24 dB
Gamma 0.45 to 1.0 (9 steps) or 257-point LUT
Image processing PRNU/DSNU, black level, flat shading and color
shading correction
Color space conversion RGB to HSI, RGB to XYZ (CIE),
sRGB, Adobe RGB, or User Custom RGB
Exposure modes No shutter, shutter select, and trigger width control
Electronic shutter 3 μs to 14.77 μs in 10 ns increments
at fastest line rate. Exposure time can be
longer at slower line rates.
Pulse width control 3 μs to 2 sec (via Camera Link)
50 ns to 2 sec (via TTL, 12-pin/10-pin connectors)
Control interface Camera Link
RS-232C
Lens mount M52 mount or Nikon F-mount
(46.5 mm flange back for both mounts)
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 10G (20 Hz to 200 Hz, XYZ directions)
Shock 50G
Regulations CE (EN61000-6-2, EN61000-6-3)
FCC Part 15 Class B, RoHS/WEEE
Power 12-pin +12V to +24V DC ± 10%
Power consumption 9.3 W typical @ +12V
Dimensions (H x W x L)
(without connector and lens mount protrusions)
90 mm x 90 mm x 90 mm
Weight 765 g
Specifications SW-4000T-MCL
SW-4000T-MCL-F
SW-4000T-MCL-M52
3-CMOS prism line scan camera with F-mount
3-CMOS prism line scan camera with M52 mount
Ordering Information
Dimensions (F-mount)
Connector pin-out
DC In / Trigger Mini-CL Interface
26
13
14
1
HIROSE HR10A-10R-12PB(71)
Pin 1 Ground
2 DC in +12V to +24V
3 Ground
4 Reserved
5 Opto in 1-
6 Opto in 1+
7 TTL out 4
8 NC
9 TTL out 1
10 TTL in 1
11 DC in +12V to +24V
12 Ground
Pin Signal Function
1 26 Power
2 15 X0-/X0+ CL Data
3 16 X1-/X1+ CL Data
4 17 X2-/X2+ CL Data
5 18 Xclk-/Xclk+ CL Clk
6 19 X3-/X3+ CL Data
7 20 SerTC+/SerTC- Serial in
8 21 SerTFG-/SerTFG+ Serial out
9 22 CC1-/CC1+ Trigger*
10 23 CC2+/CC2- Reserved
11 24 CC3-/CC3+ Not used
12 25 CC4+/CC4- Not used
13 14 GND
*Via Camera Link or 12-pin/10-pin connectors
Note:
Camera Link Base confguration shown. For
other configurations, refer to Camera Link
specifications or operation manual.
