Specifications for SW-4000T-SFP Sweep+ Series
Scanning system 3 high-speed CMOS line sensors, prism-mounted
Active pixels 3 x 4096 pixels (R, G, B)
Line rate Up to 97 kHz (variable)
Faster line rates possible with YUV compression
Sensor width 30.72 mm
Pixel size Mode A: 7.5 μm x 7.5 μm
Mode B: 7.5 μm x 10.5 μm
Ethernet speed 10GBASE-SR / 10GBASE-LR / 10GBASE-ER
Video output RGB8, RGB10V1Packed, RGB10p32,
YUV422_8_UVYV, YUV422_8
Object illuminance (min.) 220 lx @ 7800 K, Mode A
(Gain 18 dB, 525 μs exp., 50% video, RGB8)
Responsivity 123 DN/nJ/cm2
(G channel, Mode A, 10-bit @ 550 nm, 0 dB gain)
S/N ratio >55 dB on green, 10-bit with 0 dB gain
Inputs Trigger (1 Opto In + 1 TTL via 12-pin, 2 TTL via 10-pin),
Pulse Generator (4), NAND Out (2), Action (4)
Outputs 2 TTL via 12-pin, 2 TTL via 10-pin
Gain Analog Base Gain: 0 dB / 6 dB / 12 dB
Digital Master: 0 to +18 dB, R/B: -7.96 to +12 dB
Digital Individual: 0 to +24 dB
White balance Manual/one-push auto by gain or exposure
Gamma 0.45 to 1.0 (9 steps) or 257-point LUT
Image processing PRNU/DSNU, black level, flat shading and
color shading correction, chromatic aberration
adjustment, horizontal mirroring
Color space conversion RGB to HSI, RGB to XYZ (CIE),
sRGB, Adobe RGB, or User Custom RGB
Exposure modes No shutter, timed, and trigger width control
Electronic shutter 3 μs to 10.3 μs in 10 ns increments
at fastest line rate. Exposure time can be
longer at slower line rates.
Pulse width control 1.8 μs to ~1 sec
Time synchronization Support for Precision Time Protocol (IEEE 1588)
Lens mount M52 mount or Nikon F-mount
(46.5 mm flange back for both mounts)
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 3G (20 Hz to 200 Hz, XYZ directions)
Shock 50G
Regulations CE (EN61000-6-2, EN61000-6-3)
FCC Part 15 Class B, RoHS/WEEE
Power 12-pin
PoE
+10V DC to +25V DC. 11.5 W typical @ 12V
Not supported
Dimensions (H x W x L)
(without connector and lens mount protrusions)
90 mm x 90 mm x 90 mm
Weight 830 g
Specifications SW-4000T-SFP
SW-4000T-SFP-F
SW-4000T-SFP-M52
3-CMOS prism line scan camera with F-mount
3-CMOS prism line scan camera with M52 mount
Ordering Information
Dimensions (F-mount)
Connector pin-out
DC In / Trigger SFP+ Interface
HIROSE HR10A-10R-12PB(71)
Pin 1 Ground
2 DC in +12V to +24V
3 Ground
4 Reserved
5 Opto in 1-
6 Opto in 1+
7 TTL out 4
8 NC
9 TTL out 1
10 TTL in 1
11 DC in +12V to +24V
12 Ground
Spectral response
SW-4000T-SFP Sensitivity
Wavelength (nm)
Relative Response
Visit our website on www.jai.com
Europe, Middle East & Africa Asia Pacific Americas
Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444
Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300
Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners.
JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. November 2019
F-mount model shown. For M52 drawings and dimensions, see manual.
SFP+ transceiver module must support:
? 10GBASE-R
? Power level 1
Maximum fiber optic cable lengths
? 10GBASE-SR: 300m (cable type OM3)
? 10GBASE-SR: 400m (cable type OM4)
? 10GBASE-LR: 10km (cable type OS2)
? 10GBASE-ER: 40km (cable type OS2)
