Specifications for SW-8000T-SFP Sweep+ Series
Scanning system 3 high-speed CMOS line sensors, prism-mounted
Active pixels 3 x 8192 pixels (R, G, B)
Line rate (full width) Up to 49.5 kHz (variable) for 8-bit RGB
73.5 kHz possible with YUV compression
Sensor width 30.72 mm
Pixel size 3.75 μm x 5.78 μm
Ethernet speeds 10GBASE-SR / 10GBASE-LR / 10GBASE-ER
Video output RGB8, RGB10V1Packed, RGB10p32,
YUV422_8_UVYV, YUV422_8
Object illuminance (min.) 157.3 lx @ 7800 K
(Gain 30 dB, 525 μs exp., 50% video, f/2.8)
Responsivity 43 DN/nJ/cm2
(G channel, 10-bit @ 550 nm, 0 dB gain)
S/N ratio >54 dB on green, 10-bit with 0 dB gain
Inputs (Trigger) 1 Opto In + 1 TTL via 12-pin, 2 TTL via 10-pin, Pulse
Generator (4), NAND Out (2), Action (4), User Out (4)
Outputs 2 TTL via 12-pin, 2 TTL via 10-pin
Gain Digital Master: 0 to +30 dB, R/B: -4 to +12 dB
Digital Individual: 0 to +36 dB
White balance Manual/one-push auto by gain or exposure
(4000K - 9000K)
3 Presets (5000K, 6500K, 7500K)
Gamma 0.45 to 1.0 (9 steps) or 257-point LUT
Image processing PRNU/DSNU, black level, flat shading and
color shading correction, chromatic aberration
adjustment, horizontal mirroring, noise filtering
Color space conversion RGB to HSI, XYZ (CIE),
sRGB, Adobe RGB, or User Custom RGB
Exposure modes No shutter, timed, and trigger width control
Electronic shutter 3 μs to 22222 μs in 1 μs increments at 45 kHz.
Exposure time can be longer at slower line rates.
Pulse width control 1.8 μs to ~1 sec
Time synchronization Support for Precision Time Protocol (IEEE 1588)
Lens mount Nikon F-mount or M52 mount
(46.5 mm flange back for both mounts)
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 3G (20 Hz to 200 Hz, XYZ directions)
Shock 50G
Regulations CE (EN61000-6-2 and EN61000-6-3)
FCC Part 15 Class B, RoHS/WEEE, KC
Power 12-pin
PoE
+10V to +25V DC. 11.5 W typical @ 12V
Not supported.
Dimensions (H x W x L)
(without connector and lens mount protrusions)
90 mm x 90 mm x 90 mm
Weight 840 g
Specifications SW-8000T-SFP
SW-8000T-SFP-F
SW-8000T-SFP-M52
3-CMOS prism line scan camera with F-mount
3-CMOS prism line scan camera with M52 mount
Ordering Information
Dimensions (F-mount)
Connector pin-out
DC In / Trigger SFP+ Interface
HIROSE HR10A-10R-12PB(71)
Pin 1 Ground
2 DC in +10V to +25V
3 Ground
4 Reserved
5 Opto in 1-
6 Opto in 1+
7 TTL out 4
8 NC
9 TTL out 1
10 TTL in 1
11 DC in +10V to +25V
12 Ground
Spectral response
SW-8000T-SFP Sensitivity
Wavelength (nm)
Relative Response
Visit our website on www.jai.com
Europe, Middle East & Africa Asia Pacific Americas
Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444
Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300
Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners.
JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. August 2020
F-mount model shown. For M52 drawings and dimensions, see manual.
SFP+ transceiver module must support:
? 10GBASE-R
? Power level 1
Maximum fiber optic cable lengths
? 10GBASE-SR: 300m (cable type OM3)
? 10GBASE-SR: 400m (cable type OM4)
? 10GBASE-LR: 10km (cable type OS2)
? 10GBASE-ER: 40km (cable type OS2)
