Specifications for Sweep SW-4000M-PMCL and SW-8000M-PMCL
Specifications
Connector pin-out
Ordering Information
Spectral Response
Dimensions
SW-4000M-PMCL-F CMOS Monochrome Line Scan Camera with F-mount (4096 pixels)
SW-4000M-PMCL-M42A CMOS Monochrome Line Scan Camera with M42-mount* (4096 pixels)
SW-8000M-PMCL-F CMOS Monochrome Line Scan Camera with F-mount (8192 pixels)
SW-8000M-PMCL-M42A CMOS Monochrome Line Scan Camera with M42-mount* (8192 pixels)
*Note: M42-mount is M42x1 with 16 mm flange back
SW-4000M-PMCL
SW-8000M-PMCL
12-pin
connector
M-42x1 mount
F-mount
Mini-CL interface
DC In / Trigger
DC In / Trigger
Pin no. Attribute Signal Remarks
1 GND
2 Power In DC(+12V) in DC12～24 V+/-10%
3 GND
4 RESERVED
5 GND
6 I RxD in
7 O TxD out
8 GND
9 O TTL Out1
10 I TTL In1
11 POo DC(+12V) in DC12～24 V+/-10%
12 GND
12-pin connector
Mini-CL interface 26
13
14
1
Pin no. In/Out Name Note
DIGITAL I/O -1
DIGITAL I/O -2
DC IN / TRIG
POWER/ TRIG
Scanning system CMOS line scan sensor
Sensors type JAI custom made sensor (APS-C)
Sensor resolution
(effective pixels)
SW-4000M: 4096 pixels horizontal
SW-8000M: 8192 pixels horizontal
Scan rate (max) SW-4000M:
199.5 kHz (Full Camera Link 8-bit config.)
SW-8000M:
99.9 kHz (Full Camera Link 8-bit config.)
Sensor scanning width SW-4000M:
30.72 mm (Mode-A, Small well)
30.72 mm (Mode-B, Large well)
SW-8000M:
30.72 mm
Cell size SW-4000M:
7.5 um (H) x 7.5 um (V) (Mode-A, Small well)
7.5 um (H) x 10.5 um (V) (Mode-B, Large well)
SW-8000M:
3.75 um (H) x 5.78 um (V)
Responsivity SW-4000M:
58 DN/(nJ/cm2) (Mode-A, Small well)
(@10bits, gain= 1x, λ = 650nm)
53 DN/(nJ/cm2) (Mode-B, Large well)
(@10bits, gain= 1x, λ = 650nm)
23
SW-8000M:
DN/(nJ/cm2)
(@10bits, gain= 1x, λ = 650nm)
S/N ratio 60 dB @10bit (Typical)
Pixel clock 31.70 / 42.41 / 63.39 / 84.82 MHz adjustable
Video signal output 8-bit or 10-bit via Mini Camera Link connector
Inputs/Outputs GPIO in/out via 12-pin connector
Trigger mode Line start
Exposure mode
(Exposure time)
Off: Line period minus 3.6 μs (SW-4000M)
Line period minus 3.8 μs (SW-8000M)
Timed: 1.8 μs to 15.148 ms
Trigger Width: 3 μs ~
Shading correction Flat shading
Gain Manual/Auto
Digital: 0dB ~ +24dB (SW-4000), 0dB ~ +36dB (SW-8000)
Gamma 9 Step 1.0 ~ 0.45
LUT 256 point
Interface Power over Mini Camera Link
NB: Running Power over Camera Link requires 2 cables
Operating temperature -5°C to +45°C
Storage temperature -25°C to +60°C
Humidity 20 - 80% non-condensing
Vibration 10G (20 Hz to 200 Hz XYZ direction)
Shock 80G
Regulations CE (EN 61000-6-2, EN 61000-6-3), FCC part 15 class B
Power and power
consumption
PoCL or 12pin (12V to 24V DC + 10%).
435 mA/ 5.22W typical (full frame @ 12V)
NB: Running Power over Camera Link requires 2 lines
Lens mount Mount type: F-Mount
Bayonet
M-42X1 mount
Metric screw thred
Diameter: 44 mm 42 mm
Flange Back Distance: 46.5 mm 16 mm
Dimensions (H x W x L ) 62 x 62 x 84 mm (F-mount, excluding connectors)
62 x 62 x 53.5 (M42-mount, excluding connectors)
Weight 320 g
Pin no. Attribute Signal Remarks
1 GND
2 Power In DC In DC 12V tc 24V+/- 10%
3 GND
4 RESERVED
5 GND
6 I RxD in
7 O TxD out
8 GND
9 O TTL Out1
10 I TTL In1
11 Power In DC In DC 12V tc 24V+/- 10%
12 GND
Pin no. In/Out Name Note
1,26 Power DC in
2(-),15(+) O TxOUT0 Data output
3(-),16(+) O TxOUT1
4(-),17(+) O TxOUT2
5(-),18(+) O TxClk CL Clock
6(-),19(+) O TxOUT3 Data output
7(+),20(-) I SerTC (RxD)
8(-),21(+) O SerTFG (TxD)
9(-),22(+) I CC1 (Trigger) Trigger input (CC1 only)
10(-),23(+) CC1 (Reserved) (CC1 only)
11,24 NC
12,25 NC
13,14 Shield GND
January v9 2020
LVDS
(CC1 only)
serial control
