Specifications for AP-1600T-USB Apex Series
Specifications AP-1600T-USB
AP-1600T-USB
AP-1600T-USB-NF
3-CMOS prism color camera with USB3 Vision
Same as above with IR-cut filter removed
Ordering Information
Dimensions
Connector pin-out
DC In / Trigger USB 3.0 Interface
HIROSE HR10A-10R-12PB(71)
Pin 1 Ground
2 DC in +12V to +24V
3 Opto In 2-
4 Opto In 2+
5 Opto In 1-
6 Opto In 1+
7 Opto Out 1-
8 Opto Out 1+
9 TTL out 1
10
11 DC in +12V to +24 V
12 Ground
Spectral response
Relative response - sensors + prism combined
Wavelength (nm)
Spectral Sensitivity
Visit our website on www.jai.com
Europe, Middle East & Africa Asia Pacific Americas
Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444
Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300
Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners.
JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. August 2019
Outside size tolerance ± 0.3 mm
Sensor 1/2.9” 3-CMOS global shutter (IMX273)
Active pixels 1456 (h) x 1088 (v) x 3 (R,G,B)
Frame rate, full frame 78.9 frames/sec. @ 8-bit
Active area 5.02 mm (h) x 3.75 mm (v) - 6.27 mm diagonal
Pixel size 3.45 μm x 3.45 μm
System clock 74.25 MHz (for pulse generator)
Read-out modes
Full
ROI (single)
ROI (multi)
Binning
1456 (h) x 1088 (v) up to 78.9 fps
H: 16 to 1456 pixels in 16 pixel steps
V: 2 to 1088 lines in 2 line steps
Up to 5 overlapping scanning areas can be defined.
1x2, 2x1, 2x2
EMVA 1288 Parameters
Absolute sensitivity
Maximum SNR
12-bit output format
3.72 p (l = 525 nm)
40.68 dB
Traditional SNR* >60 dB (0 dB gain, 10-bit)
Video signal output 8/10/12-bits per channel?
(24/30/36-bit RGB)
Video modes Normal, Single ROI, Multi ROI, Sequencer
Gain Manual control - master mode or individual
R/G/B channels
Auto gain control - off, continuous, one-push
White balance Off, 4 presets (3200K, 5000K, 6500K, 7500K), or
one-push/continuous AWB using gain or
exposure time (3000K to 9000K)
Gamma/LUT 0.45 to 1.0 (9 steps) or 257-point programmable LUT
Shading correction Flat shading, color shading
Trigger input Opto In (2), Pulse Generators (4), Software,
NAND Out (2), User Output (4)
Exposure modes Timed/EPS, Trigger Width, Auto
Electronic shutter (can be set independently for R/G/B channels)
15.26 μs to 8 sec. in 1 μs steps (8-bit)
15.26 μs to 8 sec. in 1 μs steps (10-bit)
Auto Level Control (ALC) Shutter range from 100 μs to 13.427 ms,
gain range from 0 dB to +12 dB.
Tracking speeds and max. values adjustable.
Pre-processing functions Color enhancer, edge enhancer, color space
conversion (RGB to HSI, XYZ, sRGB, Adobe RGB),
blemish compensation (200 px/channel)
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 3G (20 Hz to 200 Hz, XYZ directions)
Shock 50G
Regulations CE (EN61000-6-2, EN61000-6-3)
FCC Part 15 Class B, RoHS/WEEE
Power 12-pin
USB 3.0
+12V to +24V DC ± 10%. 5.3 W typical @ +12 V
Bus power: not supported
Lens mount C-mount
Dimensions (H x W x L) 44 mm x 44 mm x 74 mm (excl. connectors)
Weight 170 g
Micro B type - ZX3600-B-10P or equiv.
*Traditional SNR is based on random noise in a single frame, where EMVA SNR measurements
consider more comprehensive noise sources and variance over time.
?12-bit output available in video processing bypass mode. See manual for details.
No. I/O Name Note
1 I VBUS IN Power (VBUS)
2 I/O DM USB2.0 Differential
pair (-)
3 I/O DP USB2.0 Differential
pair (+)
4 OTG ID USB OTG ID for
identifying lines
5 GND GND
6 O FX3 SSTXM USB3.0 Signal
Transmission line (-)
7 O FX3 SSTXP USB3.0 Signal
Transmission line (+)
8 GND GND
9 I FX3 SSRXP USB3.0 Signal
Receiving line (-)
10 I FX3 SSRXM USB3.0 Signal
Receiving line (+)
