Specifications for AP-3200T-PMCL Apex Series
Specifications AP-3200T-PMCL
AP-3200T-PMCL 3-CMOS prism color camera with Camera Link
Ordering Information
Dimensions
Connector pin-out
DC In / Trigger Mini-CL Interface
26
13
14
1
HIROSE HR10A-10R-12PB(71)
Pin 1 Ground
2 DC in +12V to +24V
3 Opto In 2-
4 Opto In 2+
5 Opto In 1-
6 Opto In 1+
7 Opto Out 1-
8 Opto Out 1
9 TTL out 1
10 NC
11 DC in +12V to +24 V
12 Ground
Spectral response
Relative response - sensors + prism combined
Wavelength (nm)
Spectral Sensitivity
Visit our website on www.jai.com
Europe, Middle East & Africa Asia Pacific Americas
Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444
Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300
Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners.
JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. June 2018
Outside size tolerance ± 0.3 mm
Sensor 1/1.8” 3-CMOS global shutter (IMX265)
Active pixels 2064 (h) x 1544 (v) x 3 (R,G,B)
Frame rate, full frame 55.6 frames/sec. @ 8-bit
Active area 7.12 mm (h) x 5.33 mm (v) - 8.89 mm diagonal
Pixel size 3.45 μm x 3.45 μm
Pixel clock (Camera Link) 37.125 / 74.25 / 84.85 MHz
Read-out modes
Full
ROI (single)
Binning
2064 (h) x 1544 (v) up to 55.6 fps
H: 16 to 2064 pixels in 16 pixel steps
V: 2 to 1544 lines in 2 line steps
1x2, 2x1, 2x2
EMVA 1288 Parameters
Absolute sensitivity
Maximum SNR
12-bit output format
3.66 p (l = 525 nm)
40.37 dB
Traditional SNR* >60 dB (0 dB gain, 10-bit)
Video signal output 8/10/12-bits per channel?
(24/30/36-bit RGB)
Video modes Normal, Single ROI, Multi ROI, Sequencer
Gain Manual control - master mode or individual
R/G/B channels
Auto gain control - off, continuous, one-push
White balance Off, 4 presets (3200K, 5000K, 6500K, 7500K), or
one-push/continuous AWB using gain or
exposure time (3000K to 9000K)
Gamma/LUT 0.45 to 1.0 (9 steps) or 257-point programmable LUT
Shading correction Flat shading, color shading
Trigger input Camera Link, Opto In (2), Pulse Generators (4),
Software, NAND Out (2), User Output (4)
Exposure modes Timed/EPS, Trigger Width, Auto
Electronic shutter (can be set independently for R/G/B channels)
14.73 μs to 8 sec. in 1 μs steps (8-bit)
14.73 μs to 8 sec. in 1 μs steps (10-bit)
Auto Level Control (ALC) Shutter range from 100 μs to 13.427 ms,
gain range from 0 dB to +12 dB.
Tracking speeds and max. values adjustable.
Pre-processing functions Color enhancer, edge enhancer, color space
conversion (RGB to HSI, XYZ, sRGB, Adobe RGB),
blemish compensation (200 px/channel)
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 3G (20 Hz to 200 Hz, XYZ directions)
Shock 50G
Regulations CE (EN61000-6-2, EN61000-6-3)
FCC Part 15 Class B, RoHS/WEEE
Power 12-pin
PoCL
+12V to +24V DC ± 10%. 6.0 W typical @ +12 V
+12V DC ± 10%. 6.0 W typical @ +12 V
Lens mount C-mount
Dimensions (H x W x L) 44 mm x 44 mm x 74 mm (excl. connectors)
Weight 170 g
*Traditional SNR is based on random noise in a single frame, where EMVA SNR measurements
consider more comprehensive noise sources and variance over time. ?12-bit output available in video processing bypass mode. See manual for details.
Pin Signal Function
1 26 Power
2 15 X0-/X0+ CL Data
3 16 X1-/X1+ CL Data
4 17 X2-/X2+ CL Data
5 18 Xclk-/Xclk+ CL Clk
6 19 X3-/X3+ CL Data
7 20 SerTC+/SerTC- Serial in
8 21 SerTFG-/SerTFG+ GND
9 22 CC1-/CC1+ Trigger*
10 23 CC2+/CC2- Reserved
11 24 CC3-/CC3+ Not used
12 25 CC4+/CC4- Not used
13 14 GND
*Via Camera Link or 12-pin connector
Note:
Camera Link Base configuration shown. For
other configurations, refer to Camera Link
specifications or operation manual.
