Specifications for SP-20000-CXP2
Specifications SP-20000-CXP2
Connector pin-out
Ordering Information
SP-20000M-CXP2-F Monochrome, dual-channel CoaXPress w/ F-mount
SP-20000C-CXP2-F Color, dual-channel CoaXPress w/ F-mount
SP-20000M-CXP2-M42
SP-20000C-CXP2-M42
Monochrome, dual-channel CoaXpress w/ M42-mount
Color, dual-channel CoaXPress w/ M42-mount
Dimensions
Spark Series
Spectral Response
*Traditional SNR is based on random noise in a single frame, where EMVA SNR measurements
consider more comprehensive noise sources and variance over time. For a more complete
description, see the manual.
?Reduced performance may occur when operating outside the standard range of –5°C to +45°C
Sensor 41 mm CMOS global shutter (CMV20000)
System clock 40 MHz (for pulse generator)
Frame rate, full frame 30 frames/sec.
Active area 32.77 mm (h) x 24.58 mm (v), 41 mm diagonal
Cell size 6.4 μm (h) x 6.4 μm (v)
Active pixels 5120 (h) x 3840 (v)
Horizontal output frequency 15.6 kHz to 124.8 kHz depending on tap geometry
and link configuration
Read-out modes Full
ROI
5120 (h) x 3840 (v) @ 30 fps
Any start position. 8-5120 pixels wide x
2-3840 lines high
Width in 8 pixels/step
Height in 2 lines/step
Binning (mono) 1x2, 2x1, 2x2 (frame rate does not change)
EMVA 1288 Parameters 10-bit output format
Absolute sensitivity (mono) 16.05 p (λ = 525 nm)
Absolute sensitivity (color) 18.14 p (λ = 525 nm)
Maximum SNR (mono) 40.24 dB
Maximum SNR (color) 38.32 dB
Traditional SNR* mono >53 dB (0 dB gain)
color >51 dB(0 dB gain, green)
Video signal output mono
color
8/10/12-bit monochrome
8/10/12-bit Bayer or 24-bit RGB
Some video functions not available with 12-bit
Interface CoaXPress v1.1 (CXP-6, DIN 1.0/2.3 connectors)
Link Configs: CXP6_X2, CXP6_X1, CXP3_X2,
CXP3_X1
Gain Manual/automatic 0 dB to +24 dB
White balance (SP-20000C) Manual, one-push auto, or continuous
(3000K to 9000K)
Gamma 0.45-1.0 (8 steps) or 256-point LUT
Synchronization Internal
Trigger input TTL, CXP, Pulse Generators (4), Software,
NAND Out (2), GPIO
Trigger modes EPS, Trigger Width, Timed RCT (with ALC), PIV
Electronic shutter
Timed exposure 304 μs to 8 sec in 1 μs steps
Auto shutter 1/30 to 1/3289 sec.
Auto Level Control (ALC) Shutter range from 1/30 to 1/3289,
gain range from 0 dB to +24 dB.
Tracking speeds and max values adjustable.
Pre-processing functions Flat field correction, color shading correction
(SP-20000C), blemish compensation
(up to 1000 pixels)
Operating temperature –45°C to +70°C?
Storage temperature –45°C to +70°C
Humidity 20 – 80% non-condensing
Vibration 10 G (20Hz to 200Hz XYZ)
Shock 80 G
Regulations CE (EN61000-6-2, EN61000-6-3),
FCC Part 15 class B, RoHS/WEEE
Power 12-pin
PoCXP
12V to 24V DC ± 10%. 7.9W typical @12V
24V DC ± 2V. 7.9W typical @24V
Lens mount F-mount or M42-mount
Dimensions (H x W x L) 62 mm x 62 mm x 84.5 mm
Weight 350 g
Pin Signal
1 GND
2 +12V to +24V DC input
3 GND
4 NC
5 Opto In–
6 Opto In+
7 Opto Out–
8 Opto Out+
9 TTL out 1
10 TTL in 1
11 +12V to +24V DC input
12 GND
38
62
62
52
4-M3 Depth3
F Mount
46
4
34.2 0.3 3-M3 Depth5
(9.8)
24.5
3-M3 Depth5
46
(9.8)
33.9
DC IN / TRIG AUX
CXP-1 CXP-2
LINK-1
LINK-2
POWER/ TRIG
9 11
3
(50)
φ57
Outside size tolerance ± 0.3mm
DC In / Trigger Auxiliary Connector
HIROSE HR10A-10R-12PB-01
Color response includes IR-cut filter
March 2022
Type: 3260-10S3(55) HIROSE or equivalent
Pin Signal Note
1 TTL Out 2 Line 8
2 TTL Out 3 Line 9
3 TTL In 2 Line 10
4 NC
5 GND GND
6 LVDS In 1+ Line 11 7 LVDS In 1-
8 NC
9 GND
10 GND
