Specifications for SP-25000-CXP4A Spark Series
Specifications SP-25000-CXP4A
SP-25000M-CXP4A
SP-25000C-CXP4A
25 megapixel monochrome camera with CoaXPress
25 megapixel color camera with CoaXPress
Ordering Information
Dimensions
Connector pin-out
DC In / Trigger Auxiliary Connector
HIROSE HR10A-10R-12PB(71)
Pin 1 Ground
2 DC in +10V to +25V
3 Ground
4 NC
5 Opto In 1-
6 Opto In 1+
7 Opto Out 1-
8 Opto Out 1+
9 TTL Out 1
10 TTL In 1
11 DC in +10V to +25 V
12 Ground
Spectral response
Wavelength (nm)
Relative QE (%)
Visit our website on www.jai.com
Europe, Middle East & Africa Asia Pacific Americas
Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444
Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300
Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners.
JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. March 2022
Outside size tolerance ± 0.3 mm
Sensor 26.2 MP, 1.1-inch CMOS global shutter
Active pixels 5120 (h) x 5120 (v)
Frame rate
Full frame 150 frames/sec. @ 8-bit mono/Bayer
Active area 12.8 mm (h) x 12.8 mm (v) - 18.1 mm diagonal
Pixel size 2.5 μm x 2.5 μm
Readout modes
Full
ROI (single)
Binning
5120 (h) x 5120 (v) up to 150 fps
H: 128 - 5120 pixels in 128-pixel steps
V: 8 to 5120 lines in 4-line steps
1x2, 2x1, 2x2 (mono only)
EMVA 1288 Parameters
Absolute sensitivity
Maximum SNR
12-bit output format
Mono: TBD p Color: TBD p (l = 531 nm)
Mono: TBD dB Color: TBD dB
Traditional SNR* >47 dB mono, >47 dB color (0 dB gain, 150 fps, 8-bit)
Video signal output Monochrome: mono8
Color: BayerRG8, BayerGB8, BayerGR8, BayerBG8
Video modes Normal/Single ROI, Multi ROI,
Sequencer (Trigger & Command)
Interface CoaXPress v2.0 (CXP-12, Micro BNC connectors)
Link Configs: CXP12_X4, CXP12_X3, CXP12_X2,
CXP12_X1, CXP6_X4, CXP6_X3, CXP6_X2, CXP6_X1
Gain Manual/auto 0 dB to +24 dB
White balance Off, presets (4000K, 4600K,5000K, 6500K, 7500K),
or one-push/continuous AWB (3000K to 9000K)
Gamma/LUT 0.45 to 1.0 (9 steps) or 257-point programmable LUT
Image correction &
enhancement
Flat shading, color shading (color model only),
edge enhancement
Trigger input Opto In, TTL In (2), Pulse Generators (4), Software,
NAND Out (2), User Output (4)
Exposure modes Timed/EPS, Trigger Width, Auto
Electronic shutter Timed: 9 μs to 8 s
Trigger width: 9 μs to ∞ s
Auto Level Control (ALC) Shutter range from 100 μs to ~6.6 ms,
gain range from 0 dB to +24 dB.
Tracking speeds and max. values adjustable.
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 10G (20 Hz to 200 Hz, XYZ directions)
Shock 80G
Regulations CE (EN 55032:2015, EN 55035:2017)
FCC Part 15 Class B, RoHS/WEEE
Power 12-pin
PoCXP
+10V to +25V DC. 16.5 W typical @ +12 V
Some limtations apply. See manual for details.
Lens mount C-mount (17.526 mm FBD)
Lens control Signals available via 10-pin Aux connector
Dimensions (H x W x L) 62 mm x 62 mm x 60.5 mm (incl. lens mount)
Weight 305 g
Type: 3260-10S3(55) HIROSE or equivalent
*Traditional SNR is based on random noise in a single frame, where EMVA SNR measurements
consider more comprehensive noise sources and variance over time.
Pin Signal Note
1 TTL Out 2 Line 8
2 NC
3 TTL In 2 Line 10
4 NC
5 GND GND
6 Lens Power DC 9V
7 RS-232C Tx For lens control
8 RS-232C Rx For lens control
9 GND
10 GND
