Specifications for FSFE-1600D-10GE (Flex-Eye) Fusion Series
Specifications FSFE-1600D-10GE (Flex-Eye)
FSFE-1600D-10GE 2-CMOS multispectral camera with GigE Vision
Ordering Information
Dimensions
Connector pin-out
DC In / Trigger GigE Vision Interface
HIROSE HR10A-10R-12PB(71)
Pin Signal
1 TRD+ (0)
2 TRD- (0)
3 TRD+ (1)
4 TRD+ (2)
5 TRD- (2)
6 TRD- (1)
7 TRD+ (3)
8 TRD- (3)
Spectral configuration
Visit our website on www.jai.com
Europe, Middle East & Africa Asia Pacific Americas
Phone +45 4457 8888 Phone +81 45 440 0154 Phone (Toll-Free) 1 800 445 5444
Fax +45 4491 8880 Fax +81 45 440 0166 Phone +1 408 383 0300
Company and product names mentioned in this datasheet are trademarks or registered trademarks of their respective owners.
JAI A-S Cannot be held responsible for any technical or typographical errors and reserves the right to make changes to products and documentation without prior notice. July 2020
Outside size tolerance ± 0.3 mm
Sensor 1/2.9” 2-CMOS global shutter (IMX273)
Active pixels 1440 (h) x 1080 (v) x 2 sensors
Frame rate, full frame 226 frames/sec. @ 8-bit
Active area 4.97 mm (h) x 3.73 mm (v) - 6.21 mm diagonal
Pixel size 3.45 μm x 3.45 μm
System clock 74.25 MHz (for pulse generator)
Read-out modes Full
ROI (single)
ROI (multi)
Binning
1440 (h) x 1080 (v) for each channel
H: 16 to 1440 pixels in 16 pixel steps
V: 8 to 1080 lines in 4 line steps
Up to 4 areas can be defined. No overlap.
1x2, 2x1, 2x2 (NIR only)
EMVA 1288 Parameters
Absolute sensitivity
Maximum SNR
12-bit output format
4.85 p (l = 525 nm), 10.8 p (l = 810 nm)
39.65 dB green, 39.36 dB NIR
Traditional SNR* color
NIR
>60 dB (0 dB gain, 10-bit)
>60 dB (0 dB gain, 10-bit)
Video signal output?
(Two streams)
Define 2 custom wavebands between 405-1000 nm.
Bayer sensor option for waveband located in
visible spectrum. 8/10/12-bit mono/Bayer output,
or RGB8, RGB10V1Packed, RGB10p32.
Video modes Normal, Single ROI, Multi ROI, Sequencer (2 modes)
Gain
If Bayer sensor used
Manual control - master mode 0 to +24 dB
Auto gain control - off, continuous, one-push
R/B channels - individually -7 to +15 dB
White balance
(Bayer waveband only)
Off, 4 presets (3200K, 5000K, 6500K, 7500K), or
one-push/continuous AWB (3000K to 9000K)
Gamma/LUT 0.45 to 1.0 (9 steps) or 257-point programmable LUT
Shading correction Flat shading, color shading (if Bayer selected)
Trigger input Opto In (2), Pulse Generators (4), Software,
TTL In (2), NAND Out (2), User Output (4)
Exposure modes Timed/EPS, Trigger Width (to ∞), Auto.
Delayed readout option.
Electronic shutter (can be set independently for each channel)
15.26 μs to 8 sec. in 1 μs steps
Auto Level Control (ALC) Shutter range from 100 μs,
gain range from 0 dB to +24 dB.
Tracking speeds and max. values adjustable.
Blemish compensation Up to 200 px/channel
Operating temp. (ambient) -5°C to +45°C (20 to 80% non-condensing)
Storage temp. (ambient) -25°C to +60°C (20 to 80% non condensing)
Vibration 3G (20 Hz to 200 Hz, XYZ directions)
Shock 50G
Regulations CE (EN61000-6-2, EN61000-6-3)
FCC Part 15 Class B, RoHS/WEEE
Power 12-pin +10V to +25V DC. 10.4 W typical @ +12 V
Lens mount C-mount
Dimensions (H x W x L) 62 mm x 62 mm x 86.5 mm (excl. connectors)
Weight 270 g
RJ-45 with locking screws
*Traditional SNR is based on random noise in a single frame, where EMVA SNR measurements
consider more comprehensive noise sources and variance over time.
?12-bit output available in video processing bypass mode. See manual for details.
Pin 1 Ground
2 DC in +10V to +25V
3 Opto In 2-
4 Opto In 2+
5 Opto In 1-
6 Opto In 1+
7 Opto Out 1-
8 Opto Out 1+
9 TTL out 1
10 TTL in 1
11 DC in +10V to +25 V
12 Ground
Number of wavebands 2, custom-defined
Spectral range 405-1000 nm
Minimum waveband width 25 nm
Minimum width increment 5 nm
Maximum visible waveband 405-680 nm (FWHM**)
Bayer sensor option For waveband in visible spectrum
Note: not all waveband configurations are supported.
Use JAI’s online configurator to submit desired
locations and widths for feasibility checking.
**Full width of waveband at half of its maximum
response (height)
