日照五蓮FDJ型礦井切割鋸廠商
產品介紹：
·該鋸適用于危險的工作環境，可在較高溫的環境下作業，無火花，在潮濕的環境中無漏電危險，是一款性能可靠、安全型及效率極高的理想風動工具之一。廣泛用于采礦、石化、建筑等行業。
·利用井下壓風管道系統作為動力源。重量輕，易攜帶；結構科學，便于作業。
·可快速切割管道、電纜、角鋼、結構鋼、U型鋼、鏈條、錨桿、錨索等。
·錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。
使用說明：
1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。
2、確保牢固固定了所需切割的材料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。
4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
5、關閉空氣馬達時，釋放閥桿。
6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。
8、更換鋸片前，務必?cái)嚅_(kāi)空氣軟管，并推動閥桿以釋放掉馬達內的壓力。
9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
Product introduction:
The sawblade is suitable for dangerous working environment. It can operate in a high temperature environment without sparks. It has no leakage hazard in humid environment. It is a reliable, safe and highly efficient ideal pneumatic tool. It is widely used in mining, petrochemical, construction and other industries.
Use the downhole air pressure pipe system as a power source. Light weight, easy to carry; structure science, easy to work.
It can quickly cut pipe, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on.
Super - Han metal steel alloy saw blade, high temperature resistance, wear resistance, long service life. It is very suitable for sawing stainless steel, nickel base alloy, iron, copper, aluminum, glass, plastic, wood and so on.
Instructions：
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
